Lolin32 Lite (ESP32) 8MB PSRAM Upgrade Mod

By piggybacking a PSRAM chip on to the existing flash chip we can get a whopping additional 8MB of addressable RAM.

Pseudostatic RAM (AKA PSRAM) as described on Wikipedia is, in short,

PSRAM or PSDRAM is dynamic RAM with built-in refresh and address-control circuitry to make it behave similarly to static RAM (SRAM). It combines the high density of DRAM with the ease of use of true SRAM.

The WROOM-32 based ESP32 development boards are quite versatile but they are lacking PSRAM as standard. Whereas the newer WROVER boards ship with PSRAM as the norm and is typically 4MB (megabytes) in size, but the WROVER based development boards are unfortunately almost double the cost of the WROOM-32 based development boards.

Laboris documented a successful upgrade of a ESP-WROOM-32 @ Info Upgrade ESP32 board without psRAM with 4MB/8MB SPIRAM

Sooooo, having a bunch of Lolin32 Lites at hand and a bunch of newly acquired IPUS IPS6404L-SQ SPI/QPI PSRAM, I thereby decided to give it a go. Not willing to wait until my 16MB (megabyte) flash chips arrived – my original plan was to replace them as well, which would have given a grand total of 16MB Flash/8MB PSRAM plus the original 520KB of internal SRAM, but alas impatience got the better of me and I hastily forged ahead keeping the original 4MB of flash in place.

The IPS6404L-SQ PSRAM datasheet

specifies that the PSRAM is available as a 1.8v or a 3.3v variant.

By way of flash storage the Lolin32 Lite uses the 32Mbit (4MB) 3V Winbond W25Q32JVSSIG (datasheet, click here)

and as the plan was to piggyback the PSRAM directly on to the back of the Winbond flash chip, I would need to use the matching 3V part, namely the IPS6404L-SQ-SPN version of the PSRAM and luckily that is what I have to hand, 48 of them @ £0.60 each, which per unit is actually cheaper than a 23lc1024-i/sn 1024Kbit SPIRAM part, and yes you can use the PSRAM as box standard SPIRAM.

Piggybacking an IC does mean having access to it (the IC), and the Lolin32 Lite, by not using a WROOM-32 module and having a custom design (unlike the DevkitC), has all the ICs exposed (and hence the reason I use them). Actually if you dismantled and piggybacked a WROOM-32 module you wouldn’t be able to refit the Can.

To perform the piggyback, just place the PSRAM on top of the Flash chip, in the correct orientation (i.e. Pin 1 to Pin 1, Pin 8 to Pin 8) and solder all pins excepting –

  • Pin 1 – CE/CS
  • Pin 6 – SCK

Pins 1, 6 and the 10K pull up are specific to the PSRAM (and the flash which has its own pin 1,pin 6 and resister pullup) and allow the two devices to be controlled individually.

  • Pin 1 should be wired to GPIO16 and provides the Chip Select for the PSRAM.
  • Pin 6 should be wired to GPIO17 and provides the SCLK for the PSRAM.
  • GPIO16 should be pulled up to 3V via a 10K resistor to ensure that the PSRAM is deselected during boot up.

NOTE: GPIO16 and GPIO17 will no longer be available for normal use after fitting the the PSRAM!!! Yes you just lost two pins!

As to enabling the PSRAM in PlatformIO, all that is required is to simply add the following PSRAM related build defines to your “platformio.ini” file.

After which you should hopefully see a message saying “PSRAM enabled”

Assuming that your PSRAM is enabled and active, you will now be able to use 4MB of the 8MB PSRAM as normal addressable memory, which you can subsequently allocate and use with the “ps_malloc” function.

What about the remaining 4MB, I hear you say, well the remaining 4MB of the 8MB PSRAM is accessible using the ESP32 High mem Allocation API,
a form of bank switching, where sections of ram are mapped in and out of the same address space, all of which takes me back to the good old bank switching days of Commodore 128s and Atari 130XEs, but I digress. An example doing a simple memory test of the high memory range is available at esp-idf: system/himem


ESP32-IDF: Support for external RAM

Hotchip – HT4928S Ver1.1 English PDF

The Hotchip HT4928S english datasheet

The HT4928S is a highly integrated mobile power supply Management chip with a built-in charge management module, an LED indicator Block, a boost discharge management module and is available in a small SOP8 Package. The periphery can be composed of very few components for a powerful mobile power solution.

It may or may not be the management chip that is on this module, described on Aliexpress as “5V-Step-Up-Power-Module-Lithium-Battery-Charging-Protection-Board-Boost-Converter-LED-Display-USB

With more than a little help from Google Translate, I translated the Chinese HT4928S datasheet

to English. Enjoy!